Upgraded Traktor from 1.2.4 to 1.2.7--Old .tsi won't work anymore

[Dynamics]

Hey DJTTers,

I've run into a bit of a snag where when I upgraded my traktor from 1.2.4 to 1.2.7, the .tsi(s) created are no longer working/showing up a blank list of control maps. Some sort of memory is stored within the files, it's just not being read. I was wondering if this was a known issue. This is kind of a problem for my DJ partner and I because we have two shows this week and we're opening for Dada Life next week, so I'm wondering if I'm going to have to remake all of my maps or if there was some sort of magic that can be done here.

We're running Traktor on:
-Core i7 OSX 10.6.6
&
-Intel Core 2 Duo OSX 10.6.6

[photojojo]

Unless you deleted the 1.2.4 Traktor from the computer it should still be there as upgrading doesn't overwrite the old one.

[tito]

1.2.4 store in different directory than 1.2.7 so the most probably is you can still open 1.2.4 and from there try to locate your tsi. Knowing where you put your tsi's just open 1.2.7 and import and that should be enough. Unless you erase it (service centre do not do that) or you use to store your tsi in a different folder than the traktor preferences (e.g download folder). Search on spotlight and then you find where they are and again, unless you manually deleted then they are gone.
Hope it will help

[Dynamics]

It's not that I can't find them (I store them all in a separate folder), it's that when I import them, they no longer contain any control functions.

[photojojo]

Are you using the big import button or the add>import drop down?

[Dynamics]

For the maps I made on 1.2.1, I'd use the big import button because thats how they were exported. For the ones made in 1.2.4, I'd use the little import in the add list. I've also tried both buttons for all the maps. The only one that does work was the map I created in 1.2.7 itself.

EDIT: I think at this point it's probably best to remake all of them. It is interesting that this happened. Perhaps a possible bug?

[Dynamics]

So I remade all my maps (worst five hours ever because I didn't even have the controller with me), and I came across a few more things. I was wondering if someone can clarify these for me.

I no longer get the new MIDI functions introduced in 1.2.3 such as "Is in loop" for an output.
Did they remake the default controller mappings since 1.2.4? Because the new default CDJ-400 map looks very small and not as in-depth as it did in 1.2.4.
Lastly, when I was re-doing my CDJ-400 map, I noticed that under the "Add" menu in the "Pioneer" drop-down menu, CDJ-2000, CDJ-900, and MEP-7000 blank HID maps are no longer there. Their default maps have also been removed from the Pioneer directory in default controller maps.

So many new problems.

[deviantdigi]

I haven't seen anything labeled "is in loop" as I've only used 1.2.4. Perhaps you can try whatever term is closest to that function in the Loops menu. Given the above, It also scares me that you had a Pioneer drop down menu below you add in button.

Always back up tsi's though. Good luck.

[Dynamics]

The "Is in loop" used to be in under "Add Out" in the Output menu at the bottom of the list in 1.2.4. I just use Loop Active now, but I have yet to see if it works.
Also the Pioneer drop-down menu isn't under as in underneath, but within the Add menu itself. In 1.2.4 it should contain 4 blank HID maps for the CDJ 2000, 900, 400 and MEP-7000. Mine in 1.2.7 only contains the CDJ-400.