Launchpad Mega Mapping with visual feedback

[rishi]

If there are two .tsi's then you are using the TraktorPad version. There is a Read Me with instructions for set up.

You need to install the MT Player ST.dmg (Mac). (.exe PC)
Copy the Bomes folder to documents
Open the MT Player assign ports
Then open Traktor and import the .tsi
The In an Out ports for the .tsi should be assigned to MT Player ST 1 and not Launchpad

I will make and install video and write better dock when finished but hopefully the PDF in the download will be sufficient to help you get it set up. (it's worth the effort :-)

[aviator]

Damn, I've followed the instructions to the letter and still nothing there

I can now see midi activity from within Traktor so it knows I'm pushing them buttons :-)

Just cant work out why there is nothing mapped when I import the .tsi - Have tried re-downloading the file but the same thing happened :-(

[rishi]

Sounds like you are close.

Pressing Session User1 and Mixer will bring up blank screens. You need to press User2 to access the Traktor presets.


I installed it on 3 Mac's at work yesterday so I'm pretty sure you should be able to get it working.

Here are some things to check...

First exit all and open them in this order
1. Connect Launchpad
2. Open MT Player ST
3. Open Traktor

Things to check:-
1. Make sure soundcard prefs are set and working too
2. Make sure both .tsi's are set to MT Player ST 1 for IN and OUT ports
3. Make sure you have selected the TraktorPad preset in MT Player ST
4. Check User/Documents/Bomes Midi Translator/Player ST folder exists with 3 files

Did you select Ports in the Port Chooser - They come up automatically when you run for the first time? There are two drop down boxes on a small green window.

If all the above fails you may have assigned the ports incorrectly. You can right click on MT Player and select Midi Settings to reconfigure. Select Port each Name from the drop down box and match in the Midi Port below. See Table. If the OK is greyed out the use Cancel - It means it was mapped correctly.





Good Luck!!! let me know how you go

[aviator]

You're right - I'm so bloody close its driving me nuts! LOL

Here is what I see in Controller Manager (notice no mappings)



MT Player correctly shows TraktorPad (I'm assuming the * showing is ok?)



One thing I have now noticed though is that I cant see the Bomes 1 Virtual OUT on the MIDI port assignment config.....could this be the problem?



Really appreciate your help with this Rishi, I'm determined to get this sorted as it looks like it this is EXACTLY what I need to make my launchpad a bit of usable plastic at last

[rishi]

Ok so there is def a problem with your .tsi import.

Try importing it again but use the import button down the bottom near setup wizard instead of the Add button underneath the Device drop down


MT TraktorPad is correct. Asterix is ok.

Make sure
Port Name: IN: Bome's Midi Translator 1 Virtual IN
is matched with
MIDI IN PORT: MT Player ST 1 Virtual IN

In the next update that shouldnt appear, but it is fine the way it is.

I am almost finished the next page - FX for 4 Decks'n'4FX.

Let me know how you go. To me its pretty clear the .tsi is the problem from what you have shown me.

[aviator]

Ok so there is def a problem with your .tsi import.

Try importing it again but use the import button down the bottom near setup wizard instead of the Add button underneath the Device drop down

Same thing happened

Make sure
Port Name: IN: Bome's Midi Translator 1 Virtual IN
is matched with
MIDI IN PORT: MT Player ST 1 Virtual IN

Yep, those are set correctly

Let me know how you go. To me its pretty clear the .tsi is the problem from what you have shown me.

Have tried downloading it a few times, and no difference. Also checked importing a few other .tsi's (Katapult ect) and they worked fine

[rishi]

Sheeeiiiiiit!!!!!

Send me a PM with your address and I will email you a zip of the package I loaded onto some other computers.

You are on a Mac?

[aviator]

PM sent

Thanks buddy, and yes, I'm on a mac

[rishi]

Sent you the new installer

[LopDog]

Sounds like you are close.

Pressing Session User1 and Mixer will bring up blank screens. You need to press User2 to access the Traktor presets.


I installed it on 3 Mac's at work yesterday so I'm pretty sure you should be able to get it working.

Here are some things to check...

First exit all and open them in this order
1. Connect Launchpad
2. Open MT Player ST
3. Open Traktor

Things to check:-
1. Make sure soundcard prefs are set and working too
2. Make sure both .tsi's are set to MT Player ST 1 for IN and OUT ports
3. Make sure you have selected the TraktorPad preset in MT Player ST
4. Check User/Documents/Bomes Midi Translator/Player ST folder exists with 3 files

Did you select Ports in the Port Chooser - They come up automatically when you run for the first time? There are two drop down boxes on a small green window.

If all the above fails you may have assigned the ports incorrectly. You can right click on MT Player and select Midi Settings to reconfigure. Select Port each Name from the drop down box and match in the Midi Port below. See Table. If the OK is greyed out the use Cancel - It means it was mapped correctly.





Good Luck!!! let me know how you go

i haven'( bome virtual out, just bome virtual in...
don't work for me (windows 7 user)